Skip to content
ACE FORGE HVAC — Go-green solution provider

Technical guide

PEXFit Multilayer Pipe: A Line-Set Installation Guide

A practical guide to PEX-AL-PEX line sets: five-layer construction, the fitting range, the eight-step install sequence, and the code question to settle first.

· 5 min read

A line set is the least interesting part of a mini-split installation and the most common source of a callback. This guide is the practical companion to our PEXFit vs copper comparison: that article explains where the leak risk lives and what each material demands of the installer; this one is the installation detail, the fitting range, and the questions to settle before anything is ordered.

In this guide

The deep dive: PEXFit vs Copper: Installation Time and Leak Risk

The sections on this page: what the system is · the fitting range · the application envelope · the two interfaces · the install sequence · tools · code and handling · what to put in the submittal

What the system is

The pipe is a five-layer composite: an inner layer of cross-linked polyethylene (PE-X), an adhesive layer, a continuous aluminium layer, a second adhesive layer, and an outer layer of PE-X. The aluminium seam is laser-welded.

That construction is what separates it from plain PEX, and the reason is mechanical rather than promotional:

  • The aluminium layer is a barrier. A polymer-only tube is permeable to oxygen and, over time, to refrigerant. The metal layer is what stops that diffusion — which is the property the system is actually bought for.
  • The composite is hand-formable. It bends to a radius without a bender and without annealing, which removes a tool and a hot-work step from the job.

Tube sizes cover 12, 16, 20 and 25 mm. These are the sizes the reamers, fittings and inserts are built around.

The fitting range

Five fitting types make up the mechanical system:

Fitting What it is for
Compression The standard field joint: nut, compression ring, insert, O-ring
Union A serviceable joint between two lengths
Straight Inline connection
Elbow Direction change where a bend will not fit
Solder Transition to a soldered copper connection where the system requires one

Every one of those joints depends on the same four disciplines: a square cut, a reamed and bevelled end, an insert pushed fully to the shoulder without damaging the O-ring, and a nut tightened to torque. The cluster article works through the failure modes; the point here is that the fitting range is only as good as the field practice behind it.

The application envelope

The intended envelope is mini-split and multi-split systems from 9,000 to 36,000 BTU, plus light commercial air-conditioning up to 5 ton. Sizing a job outside that range is a conversation with us, not a catalogue lookup.

Two practical limits belong in the same conversation:

  • The envelope is about the system, not just the pipe. Line length, elevation difference and the number of joints all affect the refrigerant charge and the pressure drop, and those limits come from the equipment manufacturer’s installation instructions for the unit being connected.
  • Light commercial is a different risk profile. Longer runs, more joints and more exposure mean the inspection and pressure-test discipline matters more, not less.

The two interfaces

Most mini-split work falls into one of two connection scenarios at the outdoor unit:

  1. Outdoor unit with a screw valve — the fitting is made directly onto the valve.
  2. Outdoor unit with a copper tube outlet — the composite system transitions at a copper stub, using the appropriate fitting.

Confirm which one the unit presents before the installation is planned. Getting this wrong is discovered at the wall, with the system already mounted and the vacuum pump waiting.

The installation sequence

The sequence below is the one our fitting system is designed around. It is worth reading even if you use another product, because the discipline it enforces is what keeps any compression joint dry.

  1. Cut the pipe vertically and squarely with a pipe cutter.
  2. Ream and bevel the cut end with a reamer.
  3. Select the fitting for the tube size, and place the nut and the compression ring onto the pipe.
  4. Install the fitting onto the air-conditioning valves.
  5. Push the insert into the pipe up to the shoulder — taking care not to damage the O-ring.
  6. Tighten the fitting with a wrench.
  7. Tighten the nut with a wrench.
  8. Fit the insulation sleeve.

Steps 1, 2 and 5 are where the failures come from. A cut that is not square, a burr left by the cutter, or an insert that stops short of the shoulder will produce a joint that passes a pressure test today and weeps in January.

Tools

The whole kit is a metal pipe cutter and a reamer — available in metal or plastic versions for 12, 16, 20 and 25 mm tube. That is the reason the method travels well to sites where a torch is unwelcome: occupied buildings, fire-restricted areas, and anywhere a hot-work permit is the critical path.

Add to that the usual refrigeration tooling — manifold gauges, vacuum pump, leak detector, and a torque wrench if you intend to hold the tightening discipline to a number rather than a feel.

Code acceptance and refrigerant handling — settle these first

Composite refrigerant piping is not accepted everywhere, and acceptance is a code matter decided locally. In Canada, refrigeration systems are subject to the mechanical refrigeration code and to provincial or territorial adoption of it, and refrigerant handling itself is regulated.

Before specifying any line-set material:

  • Confirm with the authority having jurisdiction that the material and the joining method are accepted for the application and the refrigerant in use.
  • Confirm that the work will be performed by qualified personnel, as the refrigerant regulations require.
  • Have the pressure test and evacuation procedure for the whole circuit in writing, including the test pressure and duration.

This is not paperwork to be handled after the purchase order. It is occasionally the answer that ends the evaluation, and it is much better learned from the AHJ than from an inspector on commissioning day.

What to put in the submittal

  • Material and construction, including the layer structure and the barrier layer.
  • Tube sizes and the fitting range, with the joining method and the specified tooling.
  • Pressure and temperature ratings of the pipe and the fittings.
  • The acceptance basis from the authority having jurisdiction, and the refrigerant handling qualifications of the installing contractor.
  • Insulation specification and the sleeve arrangement.
  • The commissioning procedure for the circuit: pressure test, evacuation, leak test, and the record that is left on site.

Where to go next

The construction, tube sizes, fitting range and application envelope we build to are on the PEXFit family page. The equipment these line sets connect is on the A-Coil, side-discharge condensing unit and mini-split SEER2 18 pages, and the rest of the connection and installation range is indexed on the products overview. For a project, put the model list and the market through the RFQ channel so the documentation set can be quoted with the equipment.